Haybusa Parts and Service Member Support

Recent Posts

Pages: 1 ... 3 4 [5] 6 7 ... 10
41
MAXIMUM OVERDRIVE / Re: Tires
« Last post by firemanjim on October 18, 2021, 11:46:31 PM »
Hard to say, Ron, it happened really fast--- heard a muffled boom-- sounded similar to when I lost a rod at Colorado Mile-- looked down and saw engine still running and no oil light---then tire left me and I was slowing fast and unable to turn the bike as it dug into the salt.
42
MAXIMUM OVERDRIVE / Re: Tires
« Last post by FlaminRoo on October 15, 2021, 03:50:19 PM »
Will try--mine first, then jack's

RIP tires, I wonder what type of stunt did you do for it to turn out like that.  :bah:

Was no stunt, at 190mph, 230mph,, shits get real, serious safety concern
43
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 12, 2021, 08:52:47 PM »
If you are going to use the 2000 16bit ecu you swap the crank trigger
from the Old motor to the new one

If you want to use the 32 bit newer ECU you will not swap the 24-1 trigger from the "newer" motor leave it in and swap the ECU

Thanks 👍🏾👍🏾👍🏾
44
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by RansomT on October 12, 2021, 07:30:20 PM »
You will need to swap some pins AND use the throttle bodies (because of the TPS) from the 2000.


The pins that need moved are as follows:
Pin 36 and Pin 43 get swapped
Pin 60 moves to 53 which is empty
Pin 56 moves to 33 which is empty
The empty holes have a little white plug in them:
45
PHOTOS/MEMBERS BIKES / Re: Just pick up this turd
« Last post by ADMIN on October 12, 2021, 04:06:24 PM »
Where did you get the garage ceiling mount rack for your bike?
46
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by Nosgsx1300 on October 12, 2021, 08:40:57 AM »
If you are going to use the 2000 16bit ecu you swap the crank trigger
from the Old motor to the new one

If you want to use the 32 bit newer ECU you will not swap the 24-1 trigger from the "newer" motor leave it in and swap the ECU
47
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 12, 2021, 06:12:39 AM »
Thanks

Do I need to  put 2000 rotor/flywheel in the 03 engine? No need to swap ecu, harness or anything else?
48
PHOTOS/MEMBERS BIKES / Re: Just pick up this turd
« Last post by busa2001 on October 12, 2021, 05:53:19 AM »
Replaced the gas tank with a Gen2, and paint it to match the bike...
49
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by Nosgsx1300 on October 12, 2021, 05:43:53 AM »
Plug it in and run it
Some say the polarity on the crack trigger is different, I have swapped mine back and forth with no noticeable difference
50
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 11, 2021, 10:00:34 PM »
Yes I have the ECU. The knock sounds like a spun bearing
Pages: 1 ... 3 4 [5] 6 7 ... 10