Haybusa Parts and Service Member Support

Recent Posts

Pages: 1 ... 4 5 [6] 7 8 ... 10
51
PHOTOS/MEMBERS BIKES / Re: Just pick up this turd
« Last post by ADMIN on October 12, 2021, 04:06:24 PM »
Where did you get the garage ceiling mount rack for your bike?
52
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by Nosgsx1300 on October 12, 2021, 08:40:57 AM »
If you are going to use the 2000 16bit ecu you swap the crank trigger
from the Old motor to the new one

If you want to use the 32 bit newer ECU you will not swap the 24-1 trigger from the "newer" motor leave it in and swap the ECU
53
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 12, 2021, 06:12:39 AM »
Thanks

Do I need to  put 2000 rotor/flywheel in the 03 engine? No need to swap ecu, harness or anything else?
54
PHOTOS/MEMBERS BIKES / Re: Just pick up this turd
« Last post by busa2001 on October 12, 2021, 05:53:19 AM »
Replaced the gas tank with a Gen2, and paint it to match the bike...
55
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by Nosgsx1300 on October 12, 2021, 05:43:53 AM »
Plug it in and run it
Some say the polarity on the crack trigger is different, I have swapped mine back and forth with no noticeable difference
56
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 11, 2021, 10:00:34 PM »
Yes I have the ECU. The knock sounds like a spun bearing
57
HELP! / Re: Help with a 2003 engine swap into a 2000
« Last post by ADMIN on October 11, 2021, 09:57:01 PM »
Did you get the ECU? Has the knock been diagnosed? They all sound like a box of rocks :D
58
HELP! / Help with a 2003 engine swap into a 2000
« Last post by MITCH1914 on October 11, 2021, 09:45:14 PM »
Need some feedback so I cam make sure I get this right.
I have a 2000 Hayabusa with really bad knock in the engine. I purchased a  complete 2003 engine that I want to swap into my 2000.
Can I plug the 2003 engine into my 2000 and it work without any problems? Or are there some changes I need to make in order for the swap to work?
59
PHOTOS/MEMBERS BIKES / Re: New Member Here
« Last post by Edward Williams on October 10, 2021, 11:19:21 PM »
Am I on the right introduction section? I am not sure since I'm a newbie.


Nice bike!
60
MAXIMUM OVERDRIVE / Re: Tires
« Last post by FlaminRoo on October 08, 2021, 07:10:48 PM »
Yeah give me the old chunk the middle out of the tire any day over that
That was the first of the new tires to see use, the old BT003 are all timing out and those RS11 and 10 were to be our replacements , Jim and i had talked it over a bit and the later generation tires seemed to be a good option to replace the old reliable ones
The Aussie bikes had them mounted in March and never turned a tire due to wind then rain, fairly sure i will be removing them and going to something like the Dunlop slicks Ralph used to run

I have had one go sort of like that on the dyno, i suspected it lost some air first as it felt odd just before the bang , tire seemed to begin delaminating then tore as it jammed

Greg, can you provide the actual tire/slick designation that Ralph used ?
Pages: 1 ... 4 5 [6] 7 8 ... 10