Haybusa Parts and Service Member Support
« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: 06 636 turbo project  (Read 28116 times)

Offline Mike-Nightrider

  • Mad Post Whore
  • ******
  • Posts: 4319
  • Gender: Male
Re: 06 636 turbo project
« Reply #25 on: January 09, 2008, 11:57:20 AM »
 :thumb: good work
Logged
Dragraceteam NIGHTRIDER
1/8: 5.101s..........1/4: 7.801s
227.7mph Woodbridge/GB 2013

Offline denmah

  • Rider
  • ***
  • Posts: 228
  • Gender: Male
    • Sloppy Mechanics
Re: 06 636 turbo project
« Reply #26 on: January 09, 2008, 06:14:01 PM »
boost controller went on tonight.... bike really likes 6psi instead of 3, wow boy  :vl:

dyno tomorrow, this was the last thing i wanted to straiten out before i went, boost + good!
Logged
Mott - // 2008 B-King // 2004 R-titled busa drag bike project

Offline denmah

  • Rider
  • ***
  • Posts: 228
  • Gender: Male
    • Sloppy Mechanics
Re: 06 636 turbo project
« Reply #27 on: January 09, 2008, 06:46:22 PM »
my dad took the liberty to do some fine tuning to the lower plastics, while i installed and played with the boost controller.




Logged
Mott - // 2008 B-King // 2004 R-titled busa drag bike project

Offline denmah

  • Rider
  • ***
  • Posts: 228
  • Gender: Male
    • Sloppy Mechanics
Re: 06 636 turbo project
« Reply #28 on: January 10, 2008, 03:04:24 PM »
VIDEO!
http://youtube.com/watch?v=CDTutyUJClc

oh yeah i went to dyno it today at scott powersports... and their dyno tech called off work. awesome for them to let me know, stupid of me not to call ahead and check, i went to ride it again, and their tech wasnt in either! i was like WTF! haha, finally called my friend there who is farther away and has a mustang dyno, even though i wanted dynojet numbers for accurate comparison, ill get a dynojet pull sometime then to check out the change after the bike is more dialed in.

Logged
Mott - // 2008 B-King // 2004 R-titled busa drag bike project

Offline kawi9

  • Rider
  • ***
  • Posts: 67
  • Gender: Male
  • ZX9R TURBO 00
Re: 06 636 turbo project
« Reply #29 on: January 14, 2008, 09:50:36 PM »
Wow good job  :thumb: What is your air fuel ratio on full throttle and full boost ? I saw about 12.8 :1 ? You don't fix the smoke problem when you start the bike ?
Logged

Offline ATLbusa

  • Post Master
  • *****
  • Posts: 1126
  • Gender: Male
Re: 06 636 turbo project
« Reply #30 on: January 15, 2008, 12:52:14 AM »
Hey to give you a heads up, look close for exhaust leaks when you cut and twist those downtubes it changes the angle of the seating face of  of the pipes.   I know this because first turbo I had built back in 97 we used the muzzy header,  and ended up with leaks around the gaskets due to this.   Ohh and it was a kawi zx9  looking good.
Logged

Offline pineygirl

  • Rider
  • ***
  • Posts: 40
Re: 06 636 turbo project
« Reply #31 on: January 15, 2008, 06:34:53 PM »
Logged
TX. Mile: Busa (Turbo) 222 mph.

Offline Smokin Ya

  • Post Whore
  • ****
  • Posts: 511
Re: 06 636 turbo project
« Reply #32 on: February 06, 2008, 08:58:38 PM »
NICE WORK!! :D :thumb:
Logged

Offline denmah

  • Rider
  • ***
  • Posts: 228
  • Gender: Male
    • Sloppy Mechanics
Re: 06 636 turbo project
« Reply #33 on: February 06, 2008, 09:34:11 PM »
all done really, did better than i expected, i gained 26hp on just 4psi of boost.

108 baseline and 135rwhp on just 4psi



just picked up a nice trailer for 300 bones!

Logged
Mott - // 2008 B-King // 2004 R-titled busa drag bike project

Offline kawi9

  • Rider
  • ***
  • Posts: 67
  • Gender: Male
  • ZX9R TURBO 00
Re: 06 636 turbo project
« Reply #34 on: February 06, 2008, 11:26:20 PM »
Nice. The number are better than the first time dyno   :thumb:   How many boost do you will run next time ?
Logged
Pages: 1 [2]  All   Go Up
« previous next »