Haybusa Parts and Service Member Support
« previous next »
Pages: [1]   Go Down

Author Topic: 01 02 gsxr  (Read 6875 times)

Offline tnfastbusa

  • Post Whore
  • ****
  • Posts: 728
  • Gender: Male
01 02 gsxr
« on: January 25, 2008, 06:16:26 PM »
is there a free manual for this year
Logged

Offline GIXXER1070

  • Rider
  • ***
  • Posts: 108
  • Gender: Male
  • Where am I?
Re: 01 02 gsxr
« Reply #1 on: January 25, 2008, 06:34:12 PM »
you can go to ron ayers or mrcycle.com and look at there microfich
Logged
Only those who will risk going to far can possibly find out how far one can go

Offline tnfastbusa

  • Post Whore
  • ****
  • Posts: 728
  • Gender: Male
Re: 01 02 gsxr
« Reply #2 on: January 25, 2008, 06:36:00 PM »
i need to know some torque spec
Logged

Offline Two Wheel Werkz

  • Rider
  • ***
  • Posts: 57
Re: 01 02 gsxr
« Reply #3 on: January 25, 2008, 08:32:25 PM »
what kind of specs you looking for?
Logged

Offline tnfastbusa

  • Post Whore
  • ****
  • Posts: 728
  • Gender: Male
Re: 01 02 gsxr
« Reply #4 on: January 26, 2008, 01:14:09 PM »
head bolts    rod bolts     and  case blots
Logged

Offline narider

  • Post Whore
  • ****
  • Posts: 826
  • Gender: Male
    • Twin Jugs Racing
Re: 01 02 gsxr
« Reply #5 on: January 26, 2008, 03:18:14 PM »
Quote from: tnfastbusa on January 26, 2008, 01:14:09 PM
head bolts    rod bolts     and  case blots

Heads=
M10's: 18ftlbs Initial & 37.6ftlbs Final
M6's: 7ftlbs
End Bolt: 10ftlbs

Rods =
15.5ftlbs intial & 90* Final

Cases=
M9's: 13ftlbs Initial & 50* Final
M8's: 10.8ftlbs Initial & 19ftlbs Final
M6's: 4.5ftlbs Initial & 8ftlbs Final

Make sure the connecting rod and headbolt threads and contact surfaces are lightly oiled,
Todd
Logged

Offline tnfastbusa

  • Post Whore
  • ****
  • Posts: 728
  • Gender: Male
Re: 01 02 gsxr
« Reply #6 on: January 27, 2008, 07:07:27 AM »
so your saying on the rods 15.5 and then 90 degrees turn that  just sounds a little low on the bolts because they are the same size as the busa
Logged

Offline narider

  • Post Whore
  • ****
  • Posts: 826
  • Gender: Male
    • Twin Jugs Racing
Re: 01 02 gsxr
« Reply #7 on: January 27, 2008, 07:52:05 AM »
No, I'm saying that's what the book said as that's what you asked for.
Todd
Logged

Offline tnfastbusa

  • Post Whore
  • ****
  • Posts: 728
  • Gender: Male
Re: 01 02 gsxr
« Reply #8 on: January 27, 2008, 08:59:49 AM »
thanks  :thumb:
Logged

Offline narider

  • Post Whore
  • ****
  • Posts: 826
  • Gender: Male
    • Twin Jugs Racing
Re: 01 02 gsxr
« Reply #9 on: January 27, 2008, 10:49:59 AM »
No problem(and I just looked it back up for you to verify that is what it states).
It of course all depends on thread pitch when it comes to the increase of a "degreed" final torque(since it's really trying to more appropriattley acheive a predetermined thread stretch), but I know that an oiled 3/8-16 Harley headbolt(probably somewhere close to a 10mm-1.50 metric thread?) initially torqued between 12-14ftlbs will result in a 42-48ftlbs final torque taking it 90* from that point.
Todd
Logged

Offline runandgun7

  • Restricted
  • Rider
  • ***
  • Posts: 209
Re: 01 02 gsxr
« Reply #10 on: August 25, 2008, 09:37:30 PM »
 :thumb:
Logged
Pages: [1]   Go Up
« previous next »