Author Topic: 08/09 Extended Tails (Read 14133 times) Tweet

Blacksj · « **on:** October 27, 2009, 07:05:01 PM »

Looking for the people who have the extended tails on the busa. Any pics please post them up. Also where do u find the fake signal stickers.

TurboGen2 · « **Reply #1 on:** October 28, 2009, 09:08:08 AM »

I installed a street +6 catalyst on mine. it had the tail light bracket and i installed an led smoked light off ebay. turned out real nice! i will get a closer pic of the tail when i get home. this is just a pic that i could at least show it looks. im extended on swingarm about 5-6 over and lowered all the way down as far as she can go! no rubbing. if extended further and too soft on rear shock then you will grab the light and shove it forward. didnt break the tail which i was really shocked. catalyst tails sure hold up.

Chance · « **Reply #2 on:** October 28, 2009, 12:15:11 PM »

Here ya go

sg1320 · « **Reply #3 on:** October 28, 2009, 01:08:32 PM »

Bikes look great. Are you guys still running the stock subframe? And if so I guess you had to cut out the back center section or unbolt it since its only there to hold up the stock undertail? And how sturdy is that catalyst tail, does it shake or bounce around at all when your riding or doing your burnouts? Id like to get the 4" street tail, I think it would be hard for someone to tell that it wasnt stock with the longer arm.

sg1320 · « **Reply #4 on:** October 28, 2009, 01:09:25 PM »

Hey chance where did you get your rotors cut?

Quote from: Chance on October 28, 2009, 12:15:11 PM

Here ya go

TurboGen2 · « **Reply #5 on:** October 28, 2009, 03:02:55 PM »

im using a tiger undertail to help brace the tail. its not much but its more than not using anything. i have asked several other peeps if they have seen my tail bouncing or moving and they say no. still using stock subframe and you just need to unbolt the 4 bolts that hold on the end of the subframe tail light support bracket. i used the street extended tail so i could still use my hump and passenger seat. with the tiger racing undertail i made another "shelf" under the tiger racing undertail out of aluminum so i could mount some more things like CO2 tank for airshifter, water tank for water injection, dl-32 datalogger, and relocated my battery to my swingarm. lots more room to fit other stuff too.

Chance · « **Reply #6 on:** October 28, 2009, 09:50:36 PM »

I have the the stock style subframe as well, with no bouncing either. I got the rotor cut from Jimmy Chance from Quality Machine out of GA, I can get you the contact info if needed. I save a little over 3lbs getting all rotors cut.
Chance

mrultra1300r · « **Reply #7 on:** October 29, 2009, 09:20:32 AM »

+6 and molded signals in

mrultra1300r · « **Reply #8 on:** October 29, 2009, 09:21:45 AM »

this tail is for sale by the way $260 shipped 48 comes with signals

Chance · « **Reply #9 on:** October 29, 2009, 10:41:29 AM »

That should sell quickly! Thats a very good price for it

soNso · « **Reply #10 on:** October 29, 2009, 11:42:54 AM »

How did you get the turn signals in the tail??? gonna buy a 6'' street tail..

mrultra1300r · « **Reply #11 on:** October 29, 2009, 12:34:37 PM »

Quote from: soNso on October 29, 2009, 11:42:54 AM

How did you get the turn signals in the tail??? gonna buy a 6'' street tail..

for 260 you can find out.

lotta time cutting and fitting. and epoxy

TurboGen2 · « **Reply #12 on:** October 29, 2009, 04:57:42 PM »

thats why i went with the integrated tail light off of ebay. it cleaned up the back end a lot.

soNso · « **Reply #13 on:** October 30, 2009, 10:49:48 AM »

Quote from: mrultra1300r on October 29, 2009, 12:34:37 PM

Quote from: soNso on October 29, 2009, 11:42:54 AM
How did you get the turn signals in the tail??? gonna buy a 6'' street tail..
for 260 you can find out. lotta time cutting and fitting. and epoxy

If it was a street tail i'd take u up on it.... but thanks for the epoxy tip.. hope i don't f___ it up. somebody should grab that tail soon.