Haybusa Parts and Service Member Support
« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: ECU editor won't connect to engine data  (Read 24794 times)

Offline PetriK

  • ECU Guru
  • Post Master
  • *****
  • Posts: 1035
  • Gender: Male
  • Where am I?
Re: ECU editor won't connect to engine data
« Reply #25 on: March 27, 2010, 03:01:53 PM »
OK, Show me if this tells that you have comports connected ... disconnecting the ftdi interface will show / not show the comport on this list.

http://macmadigan.no-ip.com/comportlist/publish.htm
Logged

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #26 on: March 27, 2010, 03:23:58 PM »
Quote from: PetriK on March 27, 2010, 03:01:53 PM
OK, Show me if this tells that you have comports connected ... disconnecting the ftdi interface will show / not show the comport on this list.

http://macmadigan.no-ip.com/comportlist/publish.htm


When I plug the flash interface in the com port list shows "com port 1" when I unplug the interface it is blank.
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline xDegeneratex

  • Apprentice Post Whore
  • **
  • Posts: 15
Re: ECU editor won't connect to engine data
« Reply #27 on: March 27, 2010, 03:37:42 PM »
Sorry about that I have a Toshiba also with windows 7 64bit. What i did was Uninstall every thing including the drivers for the cable Then logged on to admin account and re-downloaded and installed everything from there. I did try to run it from my main account and come up with the error so I have to use the admin account for flashing. Also check the security settings and allow full control to the programs I noticed that the program did bot have full control so I went in and edited the permissions to make everyone have full control for some reason it installed with limited control.
Logged

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #28 on: March 27, 2010, 08:07:55 PM »
Quote from: xDegeneratex on March 27, 2010, 03:37:42 PM
Sorry about that I have a Toshiba also with windows 7 64bit. What i did was Uninstall every thing including the drivers for the cable Then logged on to admin account and re-downloaded and installed everything from there. I did try to run it from my main account and come up with the error so I have to use the admin account for flashing. Also check the security settings and allow full control to the programs I noticed that the program did bot have full control so I went in and edited the permissions to make everyone have full control for some reason it installed with limited control.

I have also tried uninstalling all of the ports and drivers as well and reinstalling while logged in as system administrator, I don't think that I had mentioned that yet.  The security settings are set for full control for the program and com port drivers .  I am completely open to any suggestions that would help sort this issue out.  What I have learned in the last couple of weeks, is that windows 7  seems to basically be a smoothed over and re-marketed version of the old vista, that so many people including me disliked.
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline PetriK

  • ECU Guru
  • Post Master
  • *****
  • Posts: 1035
  • Gender: Male
  • Where am I?
Re: ECU editor won't connect to engine data
« Reply #29 on: March 27, 2010, 08:35:56 PM »
you can try downloading to see how it works.

http://www.ecueditor.com

Name: Hayabusa ECUeditor for K2-K7, K8- and BKing models
Version: 2.2.0.9
- com port detection method for first port changed.

Logged

Offline smithabusa

  • Boost By Smith
  • Site Supporter
  • Post Apocalyptic Whore
  • ****
  • Posts: 15353
  • Gender: Male
    • Boost By Smith
Re: ECU editor won't connect to engine data
« Reply #30 on: March 27, 2010, 08:58:11 PM »
Petri,

in case there was any doubt, I just downloaded latest version, and I didn't have issues before, but just wanted to let you know I can still successfuly read gauge data and flash with the latest software with ftdi detection changed.

Greg
Logged
Official Site Supporter

www.boostbysmith.com

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #31 on: March 27, 2010, 09:00:12 PM »
WooooHoooooo

I can confirm the data screen works, the flashing works all without EE2.2 being set as administrator on this windows 7 machine!!!

I have said this before but it needs to be said again

PetriK you are the man.  :thumb: :thumb: :thumb: :thumb: :thumb:
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline smithabusa

  • Boost By Smith
  • Site Supporter
  • Post Apocalyptic Whore
  • ****
  • Posts: 15353
  • Gender: Male
    • Boost By Smith
Re: ECU editor won't connect to engine data
« Reply #32 on: March 27, 2010, 09:02:24 PM »
Oh my god I am so happy  :D

Flatland thanks so much, if you need anything for helping out just let me know, can send some paypal your way  :thumb:

The other thing people probably don't realize, right now I think its 4 or 5 am in Finland  :bah:

Petrik you rock!
Logged
Official Site Supporter

www.boostbysmith.com

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #33 on: March 27, 2010, 09:13:38 PM »
No paypal needed, just glad that I could help out in some way with this project.

Yup I looked up the time in Finland when PetriK made the last post, about 4 a. m. ! :shock:

PetriK deserves a vast amount of respect for all the time and effort that he has invested. :thumb: :thumb: :thumb:
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline smithabusa

  • Boost By Smith
  • Site Supporter
  • Post Apocalyptic Whore
  • ****
  • Posts: 15353
  • Gender: Male
    • Boost By Smith
Re: ECU editor won't connect to engine data
« Reply #34 on: March 27, 2010, 09:21:20 PM »
yes, he most certainly does. Thanks again Petri!!!
Logged
Official Site Supporter

www.boostbysmith.com

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #35 on: March 27, 2010, 11:54:50 PM »
Another thing I ran into when switching versions of ecu editor, and thought I would mention.

Be sure to go to the control panel and uninstall the previous version of ecu editor first, before downloading the newer version, otherwise an "application can not be started" error comes up when the newer version tries to start.
« Last Edit: March 28, 2010, 12:03:08 AM by FlatlandBusa »
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline FASBUS

  • Legacy Rider
  • Post Master
  • *
  • Posts: 1286
Re: ECU editor won't connect to engine data
« Reply #36 on: March 28, 2010, 01:15:10 AM »


PetriK deserves a vast amount of respect for all the time and effort that he has invested. :thumb: :thumb: :thumb:
[/quote]

  NO DOUBT !!!!    Mad props to everybody thats helped with all phases off ecu tuning !!!!  :thumb: :thumb: :thumb: :thumb: :thumb: :thumb:
Logged

Offline Amode

  • Rider
  • ***
  • Posts: 159
  • Gender: Male
Re: ECU editor won't connect to engine data
« Reply #37 on: May 02, 2010, 11:09:10 PM »
I am having the same problem with windows 7. Will not connect to engine data. I just gave up.
Logged

Offline FlatlandBusa

  • OFF TOPIC
  • Mad Post Whore
  • **********
  • Posts: 2606
  • Gender: Male
  • -John- Middleofnowhere, Nebraska
Re: ECU editor won't connect to engine data
« Reply #38 on: May 02, 2010, 11:44:00 PM »
Follow through this thread from reply #17 on,

Make sure that you have ECU editor set to run as administrator, and FDT set to run as administrator as well if your flashing GEN1.

Also be sure to use the latest version of ECU editor, ALFA 2.2 available here,  www.ecueditor.com.
Logged
"You can not escape the responsibility of tomorrow by evading it today."
-Abraham Lincoln

Offline smithabusa

  • Boost By Smith
  • Site Supporter
  • Post Apocalyptic Whore
  • ****
  • Posts: 15353
  • Gender: Male
    • Boost By Smith
Re: ECU editor won't connect to engine data
« Reply #39 on: May 03, 2010, 06:00:16 AM »
Yep 2.2 software :)
Logged
Official Site Supporter

www.boostbysmith.com
Pages: 1 [2]  All   Go Up
« previous next »