Haybusa Parts and Service Member Support

Author Topic: Turbo ZX-12R  (Read 21810 times)

Offline TrackRat

  • Post Whore
  • ****
  • Posts: 635
Re: Turbo ZX-12R
« Reply #25 on: September 02, 2012, 08:15:26 PM »
been awhile since i updated this, had an issue with a clutch hold back spring getting into the oil pump... toasted the motor, back together with new cases, crank, rods, 1000 cc injectors, multi stage clutch. finaly having some fun, and tuning on the track now for the bigger injectors, it hasnt gone back to the dyno



having some fun with the T61 setup, so far got a best of a 1.34 60 ft, but the back half of the run was garbage. best et to date is an 8.68 @163 with a 1.44 60ft my previous best launch on a street tire was a 1.40 on my 1380, so I was happy to get in the 1.3s 3 times this past wknd. had limited runs do to a lot of issues popping up, but found solutions for all.
































Nice work....  :bike:

Kev :tu:


Living the dream.......One round at a time!

Offline KZScott

  • Post Whore
  • ****
  • Posts: 684
  • Gender: Male
Re: Turbo ZX-12R
« Reply #26 on: June 08, 2013, 03:24:39 PM »
well as usual i changed everything and missed first race, ill miss a few actually, but ill get to the track eventually.

using a Comp CT-4 6265. anti surge with billet wheel, and a .82 divided t3 hot side






same as last yr, i dont have the proper equipment or skill to tig this so im just tacking it together and will get my buddy to finish it.


Way tighter. No shimming the (full size) rad






opps... :P




Slice by my thumb and wrap up around by the cam pos sensor.....









a rather large charge cooler going in this time.











On the left. End tank from my original charge cooled frame. On the right, end tank from the new setup I'm building






Who else hates the TINY covers on a 12 frame?





charge piping ready for more tig

01 ZX-12R 8.84 @ 156.3 on dot tires, pump gas, NO power adders.... turbo 8.47 @ 164
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot... turbo 8.32 @ 173
00 ZX-12R  1: 222.046 1.5: 226.390 Loring AFB Worlds Fastest NA Kawasaki
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1  1.5: 266.5 Loring AFB Worlds fastest ZX-12R
Fabricator/Engine builder @ RCC Turbos

Offline Oz Booster

  • Site Donor
  • Mad Post Whore
  • *
  • Posts: 3968
  • aka Maj T
Re: Turbo ZX-12R
« Reply #27 on: June 08, 2013, 06:25:31 PM »
Thats a lot of work to fit that intercooler , nice job on the whole kit  :tu:
Official Site Donor

Offline KZScott

  • Post Whore
  • ****
  • Posts: 684
  • Gender: Male
Re: Turbo ZX-12R
« Reply #28 on: June 08, 2013, 07:17:17 PM »
thanks! i cut a good chunk out of either side but i added a lot of bracing to make up for it. (when in doubt over engineer :mrgreen:). just a few more pieces to finish it up. I think I might do a lexan cover instead of that aluminum one now that its all welded in. I have a secondary rail going in there
01 ZX-12R 8.84 @ 156.3 on dot tires, pump gas, NO power adders.... turbo 8.47 @ 164
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot... turbo 8.32 @ 173
00 ZX-12R  1: 222.046 1.5: 226.390 Loring AFB Worlds Fastest NA Kawasaki
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1  1.5: 266.5 Loring AFB Worlds fastest ZX-12R
Fabricator/Engine builder @ RCC Turbos