Haybusa Parts and Service Member Support
« previous next »
Pages: [1]   Go Down

Author Topic: r&d back cut tranny question  (Read 7283 times)

Offline crazybill

  • Mad Post Whore
  • ******
  • Posts: 4220
    • www.PortTechHeads.com
r&d back cut tranny question
« on: January 02, 2003, 12:58:00 PM »
anyone know what r&d gets to back cut a busa tranny and what the turn around time is ?

 perhaps even a website or # for them ?

   T.Y.
Logged
“Nobody can be so amusingly arrogant as a builder who has just discovered an old idea and thinks it is his own.”

Offline irnwkrz357

  • Post Master
  • *****
  • Posts: 1103
r&d back cut tranny question
« Reply #1 on: January 02, 2003, 01:04:00 PM »
busa tranny is already back cut.......
Logged
IRNWKRZ357 RACING
SELF PROCLAIMED BUSA,GSXR AND EVERYTHING ELSE SPECIALIST

IF ITS NOT RUNNING 8'S...MAKE NO MISTAKE ABOUT IT...ITS A TURD!

Offline crazybill

  • Mad Post Whore
  • ******
  • Posts: 4220
    • www.PortTechHeads.com
r&d back cut tranny question
« Reply #2 on: January 02, 2003, 01:09:00 PM »
well poop , you sure ?

guess ill just buy another one then...
Logged
“Nobody can be so amusingly arrogant as a builder who has just discovered an old idea and thinks it is his own.”

Offline 1WHEEL

  • Rider
  • ***
  • Posts: 296
r&d back cut tranny question
« Reply #3 on: January 02, 2003, 01:10:00 PM »
Just wondering what kind of angle is used for positive dog-slot engagement?  I have not seen one apart and the service manual photos are not very good. I would guess that the angle is less than 5 degrees. Do racing prepped engine builders increase this angle?

This is just of technical interest (I have been wondering about this for some time).  
Logged

Offline SJJBusa

  • Mad Post Whore
  • ******
  • Posts: 2399
r&d back cut tranny question
« Reply #4 on: January 02, 2003, 01:15:00 PM »
R & D Motorsports

1632 North Hercules ave.
Building G
Clearwater, Florida 33765

(727) 447-4552

Magnaflux inspection is 49.00

Undercut 2nd thru 6th is 289.00

SJJBusa
Logged

Offline Johnnycheese

  • Mad Post Whore
  • ******
  • Posts: 2196
r&d back cut tranny question
« Reply #5 on: January 02, 2003, 01:17:00 PM »
quote:
Originally posted by irnwkrz357:
busa tranny is already back cut.......
yeah right look at the differance after R&D does one.

call them and they will tell you when they are doing Suzuki trannys next then I blue lable it down there less down time
Logged
Official Site Tuner

Offline crazybill

  • Mad Post Whore
  • ******
  • Posts: 4220
    • www.PortTechHeads.com
r&d back cut tranny question
« Reply #6 on: January 02, 2003, 01:24:00 PM »
johnny , have you experienced the before/after of having this done ?
Logged
“Nobody can be so amusingly arrogant as a builder who has just discovered an old idea and thinks it is his own.”

Offline E-RACER

  • Universal Post Whore
  • *******
  • Posts: 9408
r&d back cut tranny question
« Reply #7 on: January 02, 2003, 01:34:00 PM »
I had my busa tranny done by them and a few of my oil cooled GIXXERs as well,I'll tell you,there one of the best,You will feel the difference,Its a more solid shift,and won't jump out,well worth the money IMO,My tranny broke in my busa with only 1200 non raced miles...I also added the billet shift shafts..

Just My 0.02
Logged

Offline Johnnycheese

  • Mad Post Whore
  • ******
  • Posts: 2196
r&d back cut tranny question
« Reply #8 on: January 02, 2003, 02:06:00 PM »
DAY AND NIGHT DIFFERANCE  
Logged
Official Site Tuner

Offline 9secondsflat

  • Restricted
  • Rider
  • ***
  • Posts: 268
r&d back cut tranny question
« Reply #9 on: January 02, 2003, 02:22:00 PM »
"shifts like butter"
Logged

Offline tfracing

  • Rider
  • ***
  • Posts: 211
r&d back cut tranny question
« Reply #10 on: January 02, 2003, 03:31:00 PM »
If you have the tranny done, remember to check your shift drum, and forks for wear. Also, a good idea to put in the billet fork shafts.

Had my tranny done last spring. Night and day difference in shifting smoothness.

GET IT DONE>>>
Logged
Think Fast!

  • Guest
r&d back cut tranny question
« Reply #11 on: January 02, 2003, 05:18:00 PM »
Fast By Gast did mine for my turbo bike,undercut,oversize billet output shaft,done in a couple weeks..nice work also...think it ran about $600 shipped

TFR you ever race up here at Ohio Valley??
Logged

Offline tfracing

  • Rider
  • ***
  • Posts: 211
r&d back cut tranny question
« Reply #12 on: January 02, 2003, 07:13:00 PM »
Yes, I race at Ohio Valley. LOve it especially the day after derby race.
Wish you guys had more races.

You all need to come to Clay City too.
Logged
Think Fast!

Offline len

  • Post Master
  • *****
  • Posts: 1298
r&d back cut tranny question
« Reply #13 on: January 02, 2003, 07:58:00 PM »
RnD, way to go, he'll also coat the gears, had to replace the main shaft, one fork, and both fork rods with solids , $990. about 3 weeks from out the door to back at the door. may be a little pricey, but you get what you pay for. He will get all my tranny work from now on.
Logged
MY MOMMA TOLD ME I WAS SLOW!!! What did she mean ?

Offline len

  • Post Master
  • *****
  • Posts: 1298
r&d back cut tranny question
« Reply #14 on: January 02, 2003, 08:00:00 PM »
oh yea, that also included back cutting.
Logged
MY MOMMA TOLD ME I WAS SLOW!!! What did she mean ?

Offline BADZXELEVEN

  • Post Whore
  • ****
  • Posts: 882
r&d back cut tranny question
« Reply #15 on: January 02, 2003, 10:10:00 PM »
It's gonna be atleast $850.
He's gonna sell you another kryo treated, heat treated, micro polished and coated shaft too.
ASK him about the shafts BEFORE you send it.
That way it won't suprise you like it did ME!

My shit is badass tho!  
Logged

Offline E-RACER

  • Universal Post Whore
  • *******
  • Posts: 9408
r&d back cut tranny question
« Reply #16 on: January 03, 2003, 12:18:00 AM »
I also needed a output shaft,it was cracked,Probably from my chain coming off,I was only going like 30mph when it happen,and it came right out,not locking up the wheel...but now that nice tranny is just sitting in my blown up motor,Well at least if it happens again,I have one..

             
Logged

Offline JC PAINT WORKZ

  • Post Whore
  • ****
  • Posts: 985
  • Gender: Male
  • []D [] []\/[] []D
    • JC PAINT WORKZ
Re: r&d back cut tranny question
« Reply #17 on: February 25, 2007, 10:56:07 PM »
I GOT MY TRANNY DONE BY MARK AT R&D COST ME 1590.00 BUT I GOT COMPLETLY EVERYTHING YOU CAN DO DONE TO IT. BILLET OUTPUT SHAFT, HD SURCLIPS, BACK CUT ALL GEARS, DRUM CUT, NOS CUT, ETC... CASE HARDENED IMPUT SHAFT NEW SHIFT SHAFTS, ALL NEW SHIFT FORKS... HE SAID IM PRETTY MUCH BULLET PROOF THE WAY IT SITS!!!
Logged
Pages: [1]   Go Up
« previous next »