Haybusa Parts and Service Member Support

Author Topic: 1k dogbones  (Read 6714 times)

Offline 01Busa

  • Post Whore
  • ****
  • Posts: 536
  • Gender: Male
1k dogbones
« on: October 06, 2005, 02:30:22 AM »
My Turbo busa may not be ready for my last race, so I may take the 1k, just to see what I can do on it. Question is I got the front end down okay but I want to make a set of dog bones cause i may only use them one time. How much longer hole to hole are the bones that drops it 2 inches?  Thanks for any help.  :D
01 Turbo Busa Blue & Silver (sold)
07 gsxr 1k Black & orange

Offline E-RACER

  • Universal Post Whore
  • *******
  • Posts: 9408
Re: 1k dogbones
« Reply #1 on: October 06, 2005, 02:34:40 AM »
ABOUT A INCH..

Offline 01Busa

  • Post Whore
  • ****
  • Posts: 536
  • Gender: Male
Re: 1k dogbones
« Reply #2 on: October 06, 2005, 02:47:39 AM »
Thanks e-racer  :D
01 Turbo Busa Blue & Silver (sold)
07 gsxr 1k Black & orange

Offline soupy

  • Site Supporter
  • Post Whore
  • ****
  • Posts: 760
  • Gender: Male
    • Soupys Performance
Re: 1k dogbones
« Reply #3 on: December 12, 2005, 05:20:55 PM »
I am looking for the center to center distance of the stock '05-'06 gsxr 1000 dogbones.  Can anyone help me out?  I think its 6.94.  Can anyone confirm? 

Thanks
Official Site Supporter

BLACK051K

  • Guest
Re: 1k dogbones
« Reply #4 on: January 05, 2006, 07:48:23 PM »
Just put these on my bike .
I put them up against stock bones and the stock settings on the lowering links
don't match up. Meaning if i were to back to stock height i would  be 1/4''-1/2'' higher.

On package says;  stock height
                          2'' lower
                          3'' lower

here are the #'s
« Last Edit: January 05, 2006, 08:00:08 PM by BLACK051K »

Offline soupy

  • Site Supporter
  • Post Whore
  • ****
  • Posts: 760
  • Gender: Male
    • Soupys Performance
Re: 1k dogbones
« Reply #5 on: January 05, 2006, 07:54:04 PM »
wow...those look like they'll get REALLY low on that third hole.  So....6.75" is the stock link center to center of what i am assuming is an '05 1000?

Do you have the same diagram for the stock links?

Thanks!
Official Site Supporter

BLACK051K

  • Guest
Re: 1k dogbones
« Reply #6 on: January 05, 2006, 08:34:43 PM »
wow...those look like they'll get REALLY low on that third hole.  So....6.75" is the stock link center to center of what i am assuming is an '05 1000?

Do you have the same diagram for the stock links?
 

Thanks!http
stock 05's links from center line to centerline ( black dot on tape)

« Last Edit: January 05, 2006, 10:00:42 PM by BLACK051K »

Offline badass1000

  • Post Master
  • *****
  • Posts: 1551
Re: 1k dogbones
« Reply #7 on: January 05, 2006, 09:27:47 PM »
I don't know if that will work for you.
If you want I can measure the center to center of the stock link on my 06 gsxr 1000 tomarrow.  I just went out to the garage to check, but will have to remove one of the side farings to get a accurate measurement with my digital caliper.

Offline soupy

  • Site Supporter
  • Post Whore
  • ****
  • Posts: 760
  • Gender: Male
    • Soupys Performance
Re: 1k dogbones
« Reply #8 on: January 06, 2006, 06:27:47 AM »
That is great.  Thanks!  Yes, if you could confirm that the 06 is the same length as this, I would really appreciate it!

Thanks again 05!

Official Site Supporter

BLACK051K

  • Guest
Re: 1k dogbones
« Reply #9 on: January 06, 2006, 11:07:28 AM »
05 and 06 are same

Offline badass1000

  • Post Master
  • *****
  • Posts: 1551
Re: 1k dogbones
« Reply #10 on: January 06, 2006, 12:18:24 PM »
well I ended up being buisy working today.  The 05 and 06 should be the same.  I shold be able to measure the 06 over the weekend.  I need to work on the clutch in it.

Offline soupy

  • Site Supporter
  • Post Whore
  • ****
  • Posts: 760
  • Gender: Male
    • Soupys Performance
Re: 1k dogbones
« Reply #11 on: January 06, 2006, 01:49:23 PM »
Thanks guys
Official Site Supporter

Offline spencercycle

  • Post Master
  • *****
  • Posts: 1463
Re: 1k dogbones
« Reply #12 on: January 09, 2006, 11:06:52 PM »
we have the 3 hole dog bones instock  $35 TYD  and of course the fully adjustable type for $85 TYD for the 05-06 GSXR1000

shoot me a pm or give us a call