Haybusa Parts and Service Member Support
« previous next »
Pages: [1]   Go Down

Author Topic: HOW TO REMOVE THROTTLE GRIPS?  (Read 4091 times)

Offline terco

  • Rider
  • ***
  • Posts: 483
  • Gender: Male
  • Lake Jackson Texas
HOW TO REMOVE THROTTLE GRIPS?
« on: August 26, 2006, 02:07:27 PM »
How to Install new billet grips on ?
Logged

Offline Busa Quick

  • Post Master
  • *****
  • Posts: 1226
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #1 on: August 26, 2006, 02:10:28 PM »

  The easiest way to remove the old grips is to use an air nozzle off of your air compressor and blow under the grip edge and slide them off. Then, use rubber cement to secure the new grip.


 Mark
Logged
Black and Purple 04, MY MODS: Turbo, .08 spacer, s2000 injectors, yosh cams 7.2 spring, heavy clutch springs, APE valve springs, raised rev limiter to 11,500 rpm with ignition cut only, using only stock ECM with Petrik reprogramming method,

Offline Jimzu

  • Post Whore
  • ****
  • Posts: 870
  • Gender: Male
    • Gearhead Clothing, Inc.
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #2 on: August 26, 2006, 02:13:33 PM »
Throttle grip: Remove bar end. Loosen the control housing bolts. Loosen the throttle cable adjuster. Remove throttle cable barrells from recessed carriers. Separate control housing. Remove grip. Replace with new grip. Re-install all components.

Left grip: Remove bar end. Squirt WD40 or other lubricant into grip. Wiggle and pull until removed. Clean bar. Install new grip and tighten allens. Reinstall bar end.

Should take about 15 minutes.
Logged

Offline terco

  • Rider
  • ***
  • Posts: 483
  • Gender: Male
  • Lake Jackson Texas
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #3 on: August 26, 2006, 02:22:50 PM »
Quote from: Jimzu on August 26, 2006, 02:13:33 PM
Throttle grip: Remove bar end. Loosen the control housing bolts.

how many bolts are they holding  the control togetherm I only see 1 underneath it is there another one on the front cover by a cap?
Logged

Offline terco

  • Rider
  • ***
  • Posts: 483
  • Gender: Male
  • Lake Jackson Texas
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #4 on: August 26, 2006, 02:23:30 PM »
is there another bolt on the front of the control?
Logged

Offline Jimzu

  • Post Whore
  • ****
  • Posts: 870
  • Gender: Male
    • Gearhead Clothing, Inc.
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #5 on: August 26, 2006, 02:24:10 PM »
Yes. Keep looking.
Logged

Offline terco

  • Rider
  • ***
  • Posts: 483
  • Gender: Male
  • Lake Jackson Texas
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #6 on: August 26, 2006, 02:29:37 PM »
is it cover by something?
Logged

Offline Jimzu

  • Post Whore
  • ****
  • Posts: 870
  • Gender: Male
    • Gearhead Clothing, Inc.
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #7 on: August 26, 2006, 02:44:00 PM »
They both come up through the bottom. One is next to the starter button. One is more toward the front.
Logged

Offline terco

  • Rider
  • ***
  • Posts: 483
  • Gender: Male
  • Lake Jackson Texas
Re: HOW TO REMOVE THROTTLE GRIPS?
« Reply #8 on: August 26, 2006, 03:36:12 PM »
thanks guys i got it done i will poat pics later
Logged
Pages: [1]   Go Up
« previous next »